Skip to main content

Solar Shrub II

I built this updated project in April of 2013 and posted it on Instructables



LINK TO PROJECThttps://www.instructables.com/id/Solar-Shrub-II/

Also mentioned on Treehugger.com https://www.treehugger.com/slideshows/gadgets/make-solar-shrub-charging-your-gadgets/


Solar Shrub II

It's been almost a year since I posted the original Solar Shrub on Instructables. It was a great success from the standpoint that it did what it was supposed to do (charge small devices using nothing but energy from the Sun) . Plus, winning the grand prize in the Green Tech Contest was definitely an ego boost! But there were several specific problems with the original design:

1. Low Current: The current produced was too low to charge some devices in a reasonable amount of time. I harvested the original cells from solar garden lights and the specs were quite a bit lower than I initially thought.

2. Intermittent Charging: Because it was generating power real-time and feeding it directly to the USB port, the charging capacity was only at its maximum when it was in direct sunlight. If a cloud passed over, or the cells were shaded even temporarily, the voltage dropped below 5V and the device stopped charging.

3. Difficult to Assemble: My strategy for the original project was to build “stems” with solid-conductor wires reinforced with wire clothes hangers. These stems were then pushed though holes in a base, bent to 90 degrees, and tie wrapped into place. This turned out to be extremely difficult to assemble, the stems were not as flexible as I would have liked them to be, and I had no easy way to replace a bad stem if needed without completely disassembling it. Plus the solder joints between the solar cells and the solid conductor wires tended to break easily because the wire was too rigid.

4. Vulnerable to Weather: One of the first questions I got about the original project on Instructables was, “Is it waterproof?” My answer was no, but it got me thinking. What if the it was outside charging and it started to rain?

So with these problems in mind, I set out to design a better version!

Introducing Solar Shrub II


Featuring:


Higher Output Current - I achieved higher current by purchasing 8 high-quality solar cells rated at 2-volt x 80mA. Then, with help from Joshua Zimmerman at BrownDogGadgets.com, I added a USB booster and internal lithium battery.

Combo USB Boost + Lithium Charge Controller + Lithium Battery - The combo board boosts the voltage from the cells to provide a steady 5V to the USB port. It also charges an internal lithium battery which supplements the cells when they are not in full sunlight. Once the battery is charged, I can even carry the device indoors for charging devices in the comfort of my home!

Pluggable Stems - In order to make the stems more flexible and replaceable, I decided to use stranded wire instead of solid conductors and attach the stems to the shrub base using 1/8" phono plugs and jacks. Now I can easily plug and unplug the stems as needed for quick and easy assembly and/or replacement.

A Sealed Water Resistant Enclosure - Instead of building this version into a flower pot like the original design, I built this one as a self-contained plastic “capsule” with all the electronics safely inside. The stems plug into jacks on the top of the capsule which also contains a USB cable with female connector. This design allows weather protection and much more portability. It can be placed into any flower pot or container you wish.

Comments

Popular posts from this blog

Project of the Month for May 2019

Project of the Month

This month's project is the ESP8266 Weather Station Kit by Ideaspark!
Why not buy one now and build it along with me? Here's a link via my Amazon Associates account. Purchase it here and help me support My Parts Chest website and App (available on Google Play and the Apple App Store).


ESP8266 Weather Station Kit with DHT11 Temperature Humidity BMP180 Atmosphetic Pressure BH1750FVI Light Sensor 0.96" OLED IIC YellowBlue Display for Arduino IDE IoT Starter(Guidance Document Included)
Price:$20.99

✔️The weather station uses the ESP8266-12E to obtain data from the Internet: time of a city, weather data and forecast information for the next 3 days, scrolling on the SSD1306 OLED Display; the device can switch to display data from any city in the world - maybe your relatives or friends live there✔️The device uses sensors DHT11, BMP180,BH1750FVI to collect temperature, humidity, Atmosphetic Pressure and light data. The weather station reads data indoor via sensor…

ESP8266 Weather Station

This was a fun and interesting project built from a kit by Ideaspark. It teaches you, not only how to push data to the web using an ESP8266, but also how to retrieve data from an API and parse the resulting JSON.

I built this project back in April-May of last year. I actually posted it as the Project of the Month. I got some good feedback from others who built it along with me.

As the name implies, the brains of the project is an ESP8266 microcontroller. The weather station senses local values for temperature, humidity, barometric pressure, and ambient light and uploads the data to ThingSpeak. At the same time, it also grabs weather data and 3 day forecast from the web by calling the OpenWeathermap API and outputs it on to small OLED display.

The kit includes all parts needed for the weather station:
ESP8266-12E Microcontroller w/ builtin WiFiDHT11 Humidity and Temperature sensorBMP180 Barometric Pressure sensorBH1750FVI Ambient Light sensorSSD1306 OLED DisplayUSB cableBreadboardCable…

Project of the Month for March 2019

Project of the Month

This month, I chose a robotic arm kit from MicroBotLabs. 

Why not buy one now and build it along with me? Here's a link via my Amazon Associates account. Purchase it here and help me support My Parts Chest website and App (available on Google Play and the Apple App Store).

ArmUno 2.0 MeArm and Arduino Compatible DIY Robot Arm Kit With MeCon Motion Control Software and Arduino Source Code Via Download Link
Price:$39.99

Robotic Arm Kit includes Servo motors, Structural pieces and all Fasteners needed for assembly Plus MeCon Software and Arduino Source Code Via Companion Web Site and Download Links.Windows PC Motion Control Software Allow you to Teach and Record Motion Paths for Automatic PlaybackMake your own desktop size 4-axis parallel-mechanism Mini Industrial Robotic Factory Arm!This kit features a Companion Web Site full of information resources and makes a great educational resource kit for robotics and micro controllers.Precision Laser Cut Parts Require only …